Hitek’s team of highly trained and experienced technicians calibrate your electrical test and measurement instruments so they’re performing correctly and conform to all manufacturer standards.

Choose from a standard calibration or UKAS accredited calibration service

We are able to perform electrical test equipment calibration on the following:

Description SynonymsStandard UKAS
2-4 Channel Oscilliscope
Ammeters – Up to 80A DC
Bench Meter 6.5 DigDMM - Digital Multi Meter
Bench Meter 8.5 DigDVM - Digital Volt Meter
Bench Power Supply DC Power Supply
Chart RecorderDC Power Supply
Clamp Meter/Current Clamp
Continuity Tester OHM Meter
Counters – 0.1 to 22 GHz
Current Injection Kit
Current Probes
Current/Voltage Source
Data Acquisition Switch
Data Logger
Decade Boxes
Differential Amplifier
Earth Tester Earth Bond Testers
Electronic Load
Esd StationsElectric Static Discharge Station
Esd Test EquipmentElectric Static Discharge
Flash TesterHipot Tester
Hand Held Multimeter - 3.5 Digit - 4.5 DigitDVM - Digital Volt Meter
High Voltage Probe
High Voltage Proving UnitHV Proving Unit
Insulation Tester
Lcr Meter
Lcr Meter Handheld Inductor Resistance
Line Impedence Stabilisation
Loop Calibrator
Loop Tester17th Edition Tester
Mains Analysers
Milliamp Source
Multifunction Calibrators
Multifunction Insulation Tester17th Edition Tester
Ocsilliscope Probes
Ohm Meter Resistance Meter
Pat Tester
Power AnalyserPower Meter
Power Meters
Power Supplies
Process Calibrator
Rcd TesterResidual Current Detection
Reference Sources
Resistance Box
Resistance Boxes
Resistance MeterContinuity Tester
Resistors
Rtd Simulator
Safety Analyser/Test StationPAT Testers
Safety Checkers
Scope Meter
Scopemeters
ShuntsCurrent shunts
Socket Tester
Source MeterVolt Meter, Current Meter
Stop WatchTimer, Counter
Surface Resistance MeterESD Test Meters
Tachometer (Optical)RPM Meter
Volt Meter
Volt Ratio Box/Phase Rotation Indicator
Wrist Strap Tester

17th Edition Testers

Our 17th edition tester kits come fully equipped with everything needed for electricians to test electrical installations in accordance with 17th edition regulations. We offer various combinations of single function insulation, multi-function, insulation, loop and RCD testers from top manufacturers including Fluke, Megger (MTK, MFT & PPK ranges), Martindale (2500 Part P Testing Kit), Di-Log, Kewtech and ATP.

Single Function 17th Edition Testers

We are able to calibrate all single-function electrical testers from most major manufacturers.

The three main types of single function 17th edition testers are loop testers, insulation/continuity and RCD testers.

To test a loop tester, we apply a range of values between the minimum capability of your device and the maximum possible value according to manufacturers standards. If working correctly, your tester should be able to comfortably test all readings. We also perform general operational checks, as well as ensuring that voltage and resistances of the device are correct.

For RCD testers, we perform a general operational test, and we also:

Make sure the device is carrying a current according to the manufacturer’s standards.

Check each current output range, checking trip time and trip current.

For insulation and continuity testers, we make sure that the output voltage for every insulation range conforms to manufactuer specification. We also test the full range of the device, starting with the minimum value and working up in steps towards the maximum. When testing continuity, we test every range and also make sure that the unit is zeroing correctly by testing the zero function (if it has one).

Clamp Meters

Clamp meters are tested similarly to multimeters, where the values of the tester are put through steps between the minimum and maximum to ensure it performs correctly according to the manufacturer’s specification.

We calibrate clamp meters that measure both high and low AC and DC currents as well as earth leakage and earth resistance clamp meters.

Brands: Fluke, Megger, Kewtech, Di-Log and Martindale.

PAT Testers

PAT Testers are used for electrical safety testing of office and IT equipment in domestic, commercial and industrial applications. Hitek perform a thorough test of:

  • the output current of all possible earth bond ranges
  • earth bond resistance
  • the insulation resistance for the device
  • earth leakage
  • loads and all leads supplied with a PAT tester.
  • an IEC lead and polarity test.

The main suppliers that we calibrate are Seaward, Fluke and Megger.

Multimeters

A multimeter is an electrical measuring instrument which is perfect for measuring current (AC and DC in amperes), resistance (in ohms) and voltage (AC and DC in volts) on electrical circuits. Typically, a multimeter is a combination of a DC voltmeter, an AC voltmeter, an ammeter and an ohmmeter.

Hitek offer both standard traceable calibrations and UKAS accredited calibrations on a range of on DC and Low Frequency multimeters (bench multimeters, handheld multimeters and high precision multimeters). We calibrate handheld digital multi-meters from Megger, Kewtech, Martindale, Di-Log or Fluke at up to 8 1/2 Digits.

Extra High Tension Devices

Hitek can offer standard traceable calibration services on a range of Extra High Tension (EHT) devices including:

  • High Voltage Probes
  • Flash Testers
  • Hi Pot Testers
  • Tachometers

Other Electrical Test Equipment

  • Ammeters – Up to 80A DC
  • Counters – 0.1 to 22 GHz
  • Continuity Testers
  • Current Voltage Sources
  • Data Loggers
  • Detectors – 0.1 to 18.5 GHz
  • Dummy Loads
  • Function Generators
  • HV Measurements – Up to 30kV DC
  • LCR Meters
  • Mains Analysers
  • Multi-function Calibrators
  • Oscilloscopes
  • Power Supplies
  • Reference Sources
  • Resistance Boxes
  • Resistors
  • Safety Checkers
  • Scopemeters
  • Shunt Boxes
  • Tachometers – Optical 15Hz to 10kHz
  • Timers
  • Volt Meters – Up to 1000V DC
  • Wristband Checkers